Saturday, March 30, 2013

C-band multiplier

As I required some descent L.O. signal for my NOTARS-C transverter the easiest way was to use my  Si-4133 synthesizer. The upper limit for the synthesizer is roughly 2 GHz so some kind of a simple multiplier was required. No tune multiplier as a solution can be handy (same approach as 5.7GHz multiplier) but then I will be constrained to narrow selection of L.O frequencies. Possibility to tune to various frequencies was much better cause I want to test my NOTARS-C using both, high and low side injection with IF on 144 and 432 MHz. Between several possibility, the pipe cap filter was a "best buy" option. Simple, cheap, easy to tune and not taking so much time to fabricate one.


Looking around the "acid house" i found some 3/4 pipe caps from some previous projects, so this was easy to pick up. Dead bug style is no option on microwave frequencies, so some kind of PCB is a must. Luckily I have a pile of commercial equipment PCBs where a piece was striped of with a 50ohm microstrip line. X-acto knife and a little bit of imagination and the PCB was ready. Not nice and tidy but sufficient for the quick and dirty project. The multiplier was built around two MMIC amplifiers. The first SNA-286 is running as a multiplier and the second one, ERA-5 is running as amplifier. Of course, some other MMIC can be used instead, but it is wise to use the MMICs that are working on the frequencies of interest. In my case, both MMICs are good up to 6 GHz so there should be no problem at C band at all.
 

 To force the first MMIC to act as a multiplier it is essential to saturate the MMIC just enough to produce reach harmonics. Do not push higher than maximum input power is allowed according the data sheet (dBm). I found that levels from 4-5dBm are working very good for this purposes. The higher input level will not always insure the higher output on desired harmonic frequency. Same goes for the Rb bias resistor. Increasing the value over the 80 ohm can give as a higher output level on desired harmonics too. This should be found by experiment. Do not go lower than 80 ohms because this Rb value will insure the highest allowed bias current. I found 100 ohms value to be handy for all frequencies from 2 up to 7 GHz. After filtering the required harmonic frequency with the pipe cap filter the signal is amplified with the second MMIC, ERA-5 which produce high and stable gain up to 6 Ghz. The output at 3836 Mhz was 17.6 dBm in my case, more then expected.


The pipe cap construction was straightforward. There is not much to explain, the design is quite simple. The dimensions of 3/4" are standard. In Europe they are sold under marking "22". I found the type "Vieaga 22" 22 stands for inner pipe cap diameter in mm. Inner height is 18 mm. For probes I used simple copper wire, 0.6 mm dia. Length inside the  pipe cap was 8 mm and the distance between the probes was 12.7 mm. 3/4" pipe cap will give us the possibility to tune the filter from 2 up to 7 Ghz roughly. The peak on 3896 MHz was very strong and easily found, tuned with the M4 screw.


Pipe cap filter was a good choice. The signal was clean on required frequency. At the same time the attenuation was enough on the higher harmonics not to cause any problems. Tuning around the C-band was really easy and not sharp making no problem to distinguish the 144 and 432 Mhz IF frequency. Tuning on higher harmonics other then 2nd was also easy. I manage to tune the filter even on the 4th harmonic, of course with the reduced output, but still usable and clean signal.
After all, the multiplier came out as small and handy solution. This one will probably end up as a small C-band beacon.

5 comments:

  1. This comment has been removed by the author.

    ReplyDelete
  2. Real testimony and Good news !!!

    My name is mohammad, I just received my loan and it has been transferred to my bank account, a few days ago I applied to Dangote Loan Company through Lady Jane (Ladyjanealice@gmail.com), I asked Lady jane about the Dangote Loan Company's requirements and Jane told me that if I had all the terms my loan would be transferred to me without delay

    And believe me now as my Rp11bn loan with 2% interest rate for my Coal Mining business has just been approved and transferred to my account this is a dream to come, I promise Lady jane that I will tell the world if this is true? and I'm going to tell the world right now because it's true

    You don't have to pay registration fees, license fees, comply with the Dangote Loan Company and you will get your loan

    for more details contact me via email: mahammadismali234@gmail.com and contact the Dangote Loan Company for your loan now via email Dangotegrouploandepartment@gmail.com

    ReplyDelete
  3. Hello, Do you need an emergency loan to address your financial needs? We offer loans ranging from 3,000.00 to 100,000,000.00 EUR, we are reliable, powerful, fast and dynamic, without credit control and we offer a 100% guarantee for foreign loans during the transfer period. We have also issued a loan in all currencies with a 2% interest rate for all loans .... If you are interested, contact us through Via (Whats App) number:+919394133968 patialalegitimate515@gmail.com Mr Jeffery

    ReplyDelete

  4. GET OUT OF FINANCIAL MESS WITH THE HELP OF drbenjaminfinance@gmail.com

    I have been in financial mess for the past months, I’m a single mum with kids to look after. My name is REBECCA MICHAELSON, and am from Ridley Park, Pennsylvania. A couple of weeks ago My friend visited me and along our discussion she told me about DR BENJAMIN OWEN FINANCE of (drbenjaminfinance@gmail.com); that he can help me out of my financial situation, I never believed cause I have spend so much money on different loan lenders who did nothing other than running away with my money. She advised, I gave it a try because she and some of her colleagues were rescued too by this Godsent lender with loans to revive their dying businesses and paying off bills. so I mailed him and explain all about my financial situation and therefore took me through the loan process which was very brief and easy.. After that my loan application worth $278,000.00USD was granted, all i did was to follow the processing and be cooperative and today I am a proud business owner sharing the testimony of God-sent Lender. You can as well reach him through the Company WhatsApp +19292227023 Email drbenjaminfinance@gmail.com

    ReplyDelete
  5. Do You Need A Loan To Consolidate Your Debt At 1.0%? RMPCapitals@gmail.com ( RMPCapitals@usa.com ) Or A Personal Loans * Business Loans etc. Interested Parties Should Contact Us For More Information Through Via Email: RMPCapitals@gmail.com ( RMPCapitals@usa.com )

    Do You Need A Loan To Consolidate Your Debt At 1.0%? SuiteCapitals@gmail.com ( SuiteCapitals@post.com ) Or A Personal Loans * Business Loans etc. Interested Parties Should Contact Us For More Information Through Via Email: SuiteCapitals@gmail.com ( SuiteCapitals@post.com )

    IFSCapital@post.com ( IFSCapitalloan@gmail.com ) Is Offering Its Global Fund Program, Where Loans Are Offered To Interested Clients Globally To Fund Profitable Business And Projects. Interested Parties Should Contact Us For More Information Through Via Email: IFSCapital@post.com ( IFSCapitalloan@gmail.com )

    Do You Need A Loan To Consolidate Your Debt At 1.0%? CYSCredits@Post.com ( CYSCredits@asia.com ) Or A Personal Loans * Business Loans etc. Interested Parties Should Contact Us For More Information Through Via Email: CYSCredits@Post.com
    ( CYSCredits@asia.com )

    Do You Need A Loan To Consolidate Your Debt At 1.0%? ValidusCapital@execs.com ( ValidusCapital@techie.com ) Or A Personal Loans * Business Loans etc. Interested Parties Should Contact Us For More Information Through Via Email: ValidusCapital@techie.com ( ValidusCapital@execs.com )

    ReplyDelete