Poor guy 47 GHz transverter

Having the transverter for 47GHz band may be fun if you have the near corespondent on the other side to  make some test and the QSOs on that band. If you have nobody close in the area armed with the 47Ghz radio then you need to make two transverters which may be a bit expensive. I decide to make the second transverter from the surplus available parts and using simple approach. This is why the Poor guy 47Ghz transverter was designed, just to make the first 9A-9A 47GHz QSO. 

The transverter was built around the Philips ML202938-002 upconverter band 2/4 mixer unit. I get one thanks to Goran AD6IW who also measured the performance on 47Ghz using a bit odd approach regarding the original operation and function. 

Not so many information available for the Philips mixer and the most of the information are collected by reverse engineering, opening and inspecting the unit. The unit was a part of the commercial 38 GHz equipment. As this is the upconverter, probably there should be the downconverter too (with the different code-part number). Luckily enough they are designed in manner that both can be used as the up/down converter at the same time. 

The RF input/output use the standard WR-28 flange allowing the operation on 47GHz. Local oscillator and the IF port are using the standard female SMA connectors. The unit operate as the single balanced mixer on the 38GHz. The unit has the internal tripler on the LO port where 1/3 LO frequency should be applied. The mixer diode is biased with the positive DC voltage for the best operation. We found that the +1.9V DC gave us the best results on 47GHz using the 1/4 LO frequency. And yes, I am not using the diode to multiply the LO 3 times but 4 times instead.

This way I can use the widely available DFS-1201 Synthesizer. DFS-1201 can deliver the signal in range of 11.2 - 12.0 GHz reaching the output level of +15dBm. We are limited with the step of 3.333 MHz but the FT-817d used for the IF radio can handle out of the band operation on 70cm if required. Using the 11663.33 MHz for the 1/4 LO input the resulting IF is 434.68 MHz, well within the 70cm IF radio range. 

There is also the second possibility: using the 11880 MHz for the 1/4 LO input will result the high side mixing hence the IF of -432.00 MHz and using the LSB for the standard USB operation. The reverse tuning may be odd at the beginning but the advantage is that this way the right uW band operation is sure rather then making the qso on the IF frequency if they are the same for the both transverters. 

The same IF port is used for the RX and TX side. Some kind of switching is required to switch the IF radio. In the RX chain I use also the IF amplifier where the 70cm IF is further amplified and on the TX side I am using the attenuator to bring the IF signal down to 0 dBm required for the TX mixing. To have the possibility to play with the setup all this units are made separate in the shielded boxes connected with the SMA/SMA jumper cables. The RX IF amplifier is made of two MAR-6sm mmic devices with the 1 Ghz low pass filter in between. Two mmic devices deliver around 41 db of the gain on the 432 Mhz, more than required. To reduce the excess gain and bring the S-meter down to zero extra 16 dB attenuator is added at the output reducing the IF gain to 25 dB. This clearly indicate that only one MAR-6sm is enough for the  IF RX amplifier. The same attenuator at the same time protect the RX IF mmic chain against the IF TX radio power that may damage the mixer if not properly switched through the IF switch. On the TX side I am using the standard Pi attenuator rated to meet the IF radio output power.

All this boxes are switched using two small RF Omron relays G5Y type placed on the small dedicated PCB with the female SMA connectors. This allow quick change of the setup if required and simple 76 Ghz future transverter implementation. The 47 GHz RF output is not measured but not exceeding 10uW for sure. A short peace of the WR-28 waveguide was used to connect the homebrew 25dBi pyramidal horn antenna.

And that's it, the Poor man 47 GHz transverter is ready for the operation and the first QSO. Does it work? Yes it does. I manage to make an easy qso reaching the 8 km distance without big problems even in the bad conditions, with the high humidity and temperature what can be seen in the following video. The frequency stability was not perfect but better then expected for the non shielded transverter. The other party 8 km away used the simple DB6NT 47GHz transverter running the 200 uW and the 32cm dish antenna and the IF on 144 MHz.

There is plenty room for the improvements where at the end you can get the descent 47 GHz transverter.

Fist of all, using the designed mixer topology and 1/3 of the LO frequency will result the higher LO level inside the mixer unit on the 38 GHz as there is the small filter reducing all the signals out of the 38 GHz band after the multiplier diode in the Philips mixer. To take the advantage of that the external LO should run on 12.240 Mhz. Using that approach, the IF radio should run on 10.368 MHz to reach the 47.088 MHz at the end. This should not be a big problem if we have the 3cm transverter already.

The WR-28 waveguide output is matched for the 38 Ghz operation where 47 Ghz is on the edge. To match the port on the 47 GHz and to reduce the losses due to the mismatch the matching using the small screws on the WR-28 peace of waveguide can be used.

At the end we produce the DSB signals, wasting the half of the energy and transmitting also the LO frequency. Adding the proper bandpass filter for the 47 GHz we will also reduce the NF for 3dB on the RX side. This will still result on a high overall NF of the receiver. This can be further improved by using the LNA.

The same LNA can be used on the RX but also to boost the signal on the TX side. To save the costs, the same LNA should be switched using the waveguide transfer switch.

The last advice, and maybe the simple one is to use the antenna with the higher gain. Small horn I made deliver only 25 dBi of the gain. This is handy for the quick portable operation and easy pointing and finding the right direction. The big boost will be using the dish antenna. Let say the standard 1 foot antenna which will result much stronger signal both on RX and TX side, hence much narrow angle and pointing problems.

At the end, there is no such thing as a free lunch :-)

Have fun on the 47 GHz band

Playing with the ELCOM Ceragon DFS-1201

The easiest way to get a descent local oscillator for the microwave bands is purchasing the synthesizer fabricated by the Elcom technologies Inc. Most of mine units are purchased through the E-bay from well know Israeli vendor. To be honest, I was not so lucky with that as most of the units are not working or not working properly. It is well written that the vendor does not guaranty that the units are working properly, so it is on us to decide to buy or to skip... From time to time there are some new units available, sealed, followed with the documentation. This is the way to go. True, the price is almost double but buying four units and having one descent is even more expensive :-)

Let say you get lucky and you have your unit in order, you will need the controller to run this brick. Most of the guys are using Dave - WW2R design. What yo need to know is that you have to multiply the required output synthesizer frequency by 3 and edit the ASM code just using the first 4 digits, compile the HEX and program the PIC 12F675. Plug the power and the lock LED should blink once and lighted. BINGO.

This happens if all is going by the book.

The first sign that something is going wrong may be a LED not locking the ON state. The first thing is to check if the math was ok. Let say you want to program the 11800 MHz frequency. 11800 x 3 = 35400

So you need to program the ASM two lines with the 3540. Of course, the Dave HW is supporting two frequencies, so program another convenient one.

Still not working?

Well, do not expect to have the units working out of the indicated range. Many guys are looking to have the DFS-1201 running on 12.023.333 MHz (for the 24GHz beacon) but mine experience is that the units can lock from 11.250-11.860 MHz, so even narrower than declared.

Surgery - getting a screwdriver (better a battery one :-)

You can always open the brick. If you are lazy to unscrew all those screws, check the picture:

Simple as beans soup :-) The VCO is running on 2.8-3.0 GHz. There is a buffer right after followed by the resistor splitter for the PLL and MMIC doubler 5.6-6 GHz. There is a high pass filter and another 6Ghz MMIC amplifier to provide enough power to drive the x2 multiplier diode. A long 12GHz filter then is followed by 2 stage FET amplifier. The total multiplication factor is 4. Clear ?

Guys owing the Alcatel White box 23GHz equipment needs the oscillator running on 5.9GHz. This is not so common surplus e-bay unit. DFS-1201 can do that ! All you need to do is to run the 6GHz signal from the amplifier just before the diode doubler to the output SMA connector with a peace of semirigid coax placed where the diode multiplier, 12GHz filter and 2 stage amplifier sits. All this multipliers and amplifiers (except tha last 12Ghz stage) are Sirenza S1 and S2 (ERA-1 and ERA-2 mmics) so you will have more than enough power for your White box 24Ghz transverter.

I did not play around the PLL side so much, but briefly, the reference oscillator is running on 100 MHz and heated as per above picture. The signal is then multiplied by x9 and filtered with two ceramic filters. Another mmic multiplier by x3 using INA10386 mmic followed by 2.7Ghz hairpin filter. This signal is then going to the mixer on one side and the signal from the VCO from the other side and we have the mixer output of 100-300 Mhz going to the lowpass filter and then after to the PLL. The complete picture of the digital part is here.

Most common problem is that the frequency is odd. Of course, aging of the crystal with the constant temperature is resulting to have the output frequency shifted (in my case 23khz @ 12Ghz). Just above the crystal there is a small part looking as the trimmer capacitor, so this may be re-tuned, I think so.

I had some other problem, when cold, the unit lock properly, but after some time when heated, if the unit is switched on/off I can not get the lock state and no output at all. This remain to be investigated.

On some DFS-1301 unit I can not get the lock state at all, even when cold. Checked the VCO control voltage from the charge pump and the 6V measured. It should be 5V. After playing around VCO transistor (marked 420) i manage to get the lock, VCO control voltage drop to 5V. After restarting the same problem.

This should be also investigated. And yes, to run the DFS-1301 from the Dave board, the output frequency should be multiplied by 2 or divided by 5. Funny math, you get the same first for digits :-) to program the ASM code.

So that's all for now, at least my DFS-1295 is working properly if nothing else :-)

Eyal Gal - 24GHz transverter

Coming back

For some time there was no new post from me, but here is the one that can be handy and interesting. I will try to bring your attention on this peace oh the "aluminum brick" called Eyal Gal transceiver. If you have one or if you are planing to buy one then you already have the G8CUB paper about it and the basics about building the 24GHz transverter.

Word of discouragement

Buying the Eyal Gal transceiver unit is just a half way to a working transverter, maybe not even a half way, let say 40%. I learn that on my unit, so be prepared to some extra sacrifices :-) and hiding the money from your wife :-) I will try not to repeat the good Roger Ray G8CUB article about this unit. Instead of that I will try to present my itinerary and the way how I made this thing to transmit.

First thing - shopping (Eyal Gal and ELCOM Ceragon)

I obtain my unit (two units) from the "24GHz microwave store" owned by a really BIG gentleman Ernie -HG5ED. It was a big gift from a big guy like he is. He knew that this is just a half of the story, so he included the local oscillator to drive this wild machine. Yes, you need the external local oscillator too, so start saving the money.... The local oscillator should work on the half frequency and what is required is the high side injection. As I choose the 70cm IF, the local oscillator should run on 12240MHz. This can be done using the various techniques, from the endless multipliers chain to the expensive low phase noise oscillators. My local oscillator is the CDFS-1295, ELCOM-Ceragon unit that can be found from time to time on the E-bay. More likely you will find the DFS1201 Ceragon unit that can operate from 11-12Ghz which is not good for this radio, we need the 1295  model running from 12-13Ghz. Whatever, you need the 10dBm @ 12240MHz signal. If you plan to use the Ceragon LO's then you need also the controller to run this unit. The controller can be found around the web together with the software for the PIC.

Second thing - more shoping (power supply)

OK, so you have the transceiver, the local oscillator and now you need the descent power supply for the Eyal Gal unit. As you already know, +8V, +12V and -12V  are required for this unit. I start to make the first test with the old PC power supply where +/-12V is available and +8V was produced with a single 7808 voltage regulator. This can work, but if you plan to run your transverter portable on the car battery then the PC power supply is not a good option.The tricky part is obtaining -12V and 120mA. For that purpose I use the DC/DC converter (thanks to Ernie) where I have the +/-12V and 250mA output which should be more than enough for the negative supply. The positive 12V is obtained from the 12V rail external power supply or the battery. 

Another tricky part may be the +8V where the consumption may reach over 1A in TX. This can be solved with the switching units. To make things simple, I use two 7808 regulators in parallel with the diode on the output. All the voltage regulators are fixed to the good heatsink.

Finally some soldering (IF switching unit)

So beside the L.O. delivering 10dbm you need a IF radio delivering -21dbm for the proper mixing. Of course, the attenuators are used. Take care, if you ran the IF radio with 2w of output you need 54dB of attenuation on 70cm which is not a trivial. If you used the relay for switching, it should be a good one, with the good isolation. Instead of that, I use the old fashioned switching with the PIN diodes. It is true that also on the RX side I have something about 5db of attenuation, I cure the problem with an extra MMIC amplifier in the RX side of IF switching unit. Of course, I was faced then with the extra gain and s-meter showing S-2. Then extra attenuator was introduced, which is not bad idea as the mmic see the nice 50ohms on input/output.

All those PINS (Eyal Gal transceiver)

The Eyal-Gal unit is a transceiver and not so much to switch around it. To make a story short, you need to key only PIN 1 and all the rest of the pins you can leave n/c. 

But who want to know more:

Pin 1 is described as TX inhibit pin. It mean that you need to ground this pin when on RX and lift up when on TX. This will result better reception and less current consumption that leads to less heating of the Eyal-Gal at the end. So do not forget, PIN 1 to GND when on RX.

Pins 2 and 3 are n/c ( I love when the pins are n/c :-)

Pin 4 is 0V ( I left my n/c as I have enough ground through the housing )

Pin 5 is AGC To be correct, you can reduce the TX conversion gain by applying 0-5V dc. Leaving this port n/c :-) you will have the maximum gain (and the output power)

Pin 6 is a output power detector, where you can see by the DC voltage if you have the output power. I measure a bit more than 3V DC on that pin when on TX. Do not expect the voltage following the modulation! You will have constant (more or less) DC voltage as there is the 2xLO signal and both mixing products measured. This is why you need a filter on the TX output side !

Pin 7 is the RX AGC control. Well it works the same way like the pin 5, if n/c you will have the highest RX gain, if 0-5V dc applied you can reduce the RX gain.

Filtering (spending more money)

The output filter on the TX side is a MUST. Do not operate the transceiver without it because you may interfere with some cell tower links. You do not want to do that. You will have to look for a experience microwave guy help here or buy the tuned filter for the desired frequency.

Antenna switching

You probably heard the stories that antenna relay for the 24GHz operation should be a waveguide switch and nothing else... So why there are SMA coaxial relays on the market rated to operate up to 26.5GHz ? The E-bay is good source of such relays with a fair prices. More over the latching relay type can be purchased really cheap. Using the SMA relay will save you a troubles bending the waveguides, using the flexible waveguide and at the end the waveguide switch is really expensive. So the SMA coaxial relay is not only a cheaper but occupy less space and the box can be smaller, which also reduce the final cost of the transverter.

I did not measure the difference and the losses, but messing with the waveguide switch comparing to the SMA relay is not worth money and time.

First tests

Even the desk measurements on the instrumens were OK, the real test was performed listening the live signal on the band. Observe the frequency stability of the Eyal Gal transverter and the Mini beacon running some 4km away. The mini beacon will be explained in the next article. Note: none of the units were conected to the GPSDO reference.

Finally results :-)

At the end, what can be done with the 24GHz transverter described, so far I made the 236km QSO in a not so good conditions, means humidity 60%, temp 17 degC and pressure 1016hPa. The antenna used was a "footer" 32cm dish. The qso was a SSB with a solid copy both sides. Well, do not forget to switch the LSB on your radio when operating USB due to high side mixing. The drawback is that the tuning the frequency is opposite, but this should not be a problem for a experienced microwave operator.

Have fun.....

13cm NO TUNE doubler - multiplier

After some time I am back :-)

The multiplier layout on the LNA4HF PCB

...and the real doubler

NOTARS-S Transverter 13cm band

NO Tune And Really Small, this time for 13cm band...
After successful testing of NOTARS-C band transverter for the 3400 MHz it was just a matter of time to do the same with the transverter for the S band. It means this transverter can be used on all 13cm bands world wide 2304 MHz, 2320 MHz, 2401 MHz etc... It can be used also as the  S53MV NBP ( Non-Flawless Protocol) transverter for up converting the 70cm band to 13 cm or 9 cm ( using the NOTARS-C ) Low side or high side L.O. injection - it does not matter until we use the 70cm band for the I.F.

The beer bottle caps are not the part of the project, they are here just to give you the idea of the transverter size. Maybe this beer caps are good for filters up on the 6cm band but not here :-) This is the prof of project board and the final PCB should be even smaller, there is a plenty room for the resizing making everything working the same on less FR-4 substrate. There is a short video showing the reception from the other 13cm transverter using just a Wi-Fi vip antenna.

It can be noted that the frequency stability is quite OK. For the L.O. in the video I am using Si-4133 synthesizer running at 1888 Mhz requiring 432 Mhz for the I.F. for the successfully operation on the 2320 MHz what became a standard in the Europe. For other 13cm band plans scheme just drive the other L.O. frequency. The other side 13cm transverter (transmitting on the video) is using a crystal oscillator with the multiplier to reach the desired L.O. frequency. after a couple of minutes, the stability was also good.

The transmitting part is working also nice, producing more then 18dBm (70mW) of power on 2320 Mhz. This can be enough for rover type operation with the standard Wi-Fi antenna. A small sequencer with the power attenuator and you are ready to go. The on board filters are reducing the unwanted mixer products and L.O. signal almost 50dBc without any external filter. The twins from the picture are ready for the operation. For a moment we will stop here, NOTARS for 5760Mhz is not yet ready.

C-band multiplier

As I required some descent L.O. signal for my NOTARS-C transverter the easiest way was to use my  Si-4133 synthesizer. The upper limit for the synthesizer is roughly 2 GHz so some kind of a simple multiplier was required. No tune multiplier as a solution can be handy (same approach as 5.7GHz multiplier) but then I will be constrained to narrow selection of L.O frequencies. Possibility to tune to various frequencies was much better cause I want to test my NOTARS-C using both, high and low side injection with IF on 144 and 432 MHz. Between several possibility, the pipe cap filter was a "best buy" option. Simple, cheap, easy to tune and not taking so much time to fabricate one.

Looking around the "acid house" i found some 3/4 pipe caps from some previous projects, so this was easy to pick up. Dead bug style is no option on microwave frequencies, so some kind of PCB is a must. Luckily I have a pile of commercial equipment PCBs where a piece was striped of with a 50ohm microstrip line. X-acto knife and a little bit of imagination and the PCB was ready. Not nice and tidy but sufficient for the quick and dirty project. The multiplier was built around two MMIC amplifiers. The first SNA-286 is running as a multiplier and the second one, ERA-5 is running as amplifier. Of course, some other MMIC can be used instead, but it is wise to use the MMICs that are working on the frequencies of interest. In my case, both MMICs are good up to 6 GHz so there should be no problem at C band at all.

 

 To force the first MMIC to act as a multiplier it is essential to saturate the MMIC just enough to produce reach harmonics. Do not push higher than maximum input power is allowed according the data sheet (dBm). I found that levels from 4-5dBm are working very good for this purposes. The higher input level will not always insure the higher output on desired harmonic frequency. Same goes for the Rb bias resistor. Increasing the value over the 80 ohm can give as a higher output level on desired harmonics too. This should be found by experiment. Do not go lower than 80 ohms because this Rb value will insure the highest allowed bias current. I found 100 ohms value to be handy for all frequencies from 2 up to 7 GHz. After filtering the required harmonic frequency with the pipe cap filter the signal is amplified with the second MMIC, ERA-5 which produce high and stable gain up to 6 Ghz. The output at 3836 Mhz was 17.6 dBm in my case, more then expected.

The pipe cap construction was straightforward. There is not much to explain, the design is quite simple. The dimensions of 3/4" are standard. In Europe they are sold under marking "22". I found the type "Vieaga 22" 22 stands for inner pipe cap diameter in mm. Inner height is 18 mm. For probes I used simple copper wire, 0.6 mm dia. Length inside the  pipe cap was 8 mm and the distance between the probes was 12.7 mm. 3/4" pipe cap will give us the possibility to tune the filter from 2 up to 7 Ghz roughly. The peak on 3896 MHz was very strong and easily found, tuned with the M4 screw.

Pipe cap filter was a good choice. The signal was clean on required frequency. At the same time the attenuation was enough on the higher harmonics not to cause any problems. Tuning around the C-band was really easy and not sharp making no problem to distinguish the 144 and 432 Mhz IF frequency. Tuning on higher harmonics other then 2nd was also easy. I manage to tune the filter even on the 4th harmonic, of course with the reduced output, but still usable and clean signal.

After all, the multiplier came out as small and handy solution. This one will probably end up as a small C-band beacon.

NOTARS-C Transverter 3400 MHz

Mine is smaller than the other :-)
The only thing that men are fighting about the smaller one is the mobile phone. Well, not just the mobile phone, but also we can say, the transverter. Everybody is looking for the smaller and better.

You may ask why NOTARS ?
NO Tune And Really Small - C band transverter. Easy and simple, plug and pray solution. No tuning parts, no expensive laminate, fixed filters, simple layout. Of course, it can be even smaller by using 0603 instead of 0805 SMD parts but do we need such a small transverter ?

Small ha...

5.7 GHz poor guy transverter

Not so many simple transverters for 6cm band seen up to now. So here is one, really simple and working, with minimum parts required and poor guy like me did find all the parts within the pile of microwave "LEGO bricks".

The architecture is traditional and straightforward, no bells and whistles in this design. The core of the transverter is the mixer. Simple as it can be, SKY-60 double balanced mixer working up to 6GHz with affordable price, new through the e-bay purchase. Drive on the IF port 0dBm @ 432MHz, +7dBm @ 5328MHz for the LO port. On the output RF port we have LO, LO+432MHz and LO-432MHz signal present. To get rid of the unwanted signals the mixer is followed by the filter. Here we can use many types of filters but the pipe cap was a simple and cheap solution, can be tuned easily even with no special measuring equipment. Tune to peak method will give good results. Of course the frequency is 5760MHz. This filter will be used both , for RX and TX operation. PIN diodes, RF switch, relay, resistor splitter or Wilkinson divider. Well, the Wilkinson divider was appropriate and simple enough for this approach. More over, no switching required for RX/TX operation. I made mine from the old 1.8GHz cellular equipment easily cutting out the peace of the PCB with the printed divider. Simple calculation, sharp x-act knife and the divider legs were modified to L/4 @ 5.760MHz. This way I end up with two ports, one for the RX and the other for the TX side of the transverter. For the RX front end i choose not the best, but cheap and simple MMIC block with the MGA-86563 declared to work up to 6GHz with not so bad performance. The MMIC was biased for the maximum gain with 8V power supply. On the transmitting side there is also a MMIC block, simple Sirenza SNA-586 good up to 6GHz biased for the maximum gain with 8V power supply. 

So this is it, a simple transverter, of course with the limited performance but good for the quick qso with the neighbor station or somebody on the hill within the line of sight. To operate this transverter we need some kind of local oscillator and a simple electronics handling the power and antenna switching. Crystal oscillator with the chain of multipliers can give us maybe better phase noise but better stability and more flexibility in choosing the IF insure the synthesizer built fir microwave frequencies. I choose the VK3XDK Si-4133 synthesizer version with the 16 programmable frequencies. The synthesizer is locked to high quality 10MHz double oven oscillator granting excellent stability and lower phase noise comparing to the cheap 10MHz canned oscillators. I prefer to use the 70cm IF so the LO was programmed to 1776MHz. The 13dBm output was attenuated with the 7db attenuator to safely drive the 3x multiplier box producing some 15dBm of the signal @ 5328MHz. Again 7db attenuator between the multiplier and mixer to bring the signal to the required mixer level. At the same time the mixer was very happy to "see" the 50 ohms impedance at any port. For this experiment i choose the IF 432MHz, but much better will be 434 or higher. Not more than 0dBm is required on the mixer IF port, so the 27dBm (500mW) signal from the FT-817d was reduced with the 26db attenuator at the sequencer board. Sequencer is also switching the power for the MMICs in the transverter as well as the power for the coaxial relay at the output. RF sensing and PTT ports insuring high protection. If the coaxial relay or RF electronic switch is not available we can use two separate antennas for the RX and TX. With this arrangement the setup is ready for the smoke test and initial qso testing. The output power is low, not reaching not even 1mW and the conversion gain is also poor just a few db so some extra amplification is required for serious work. 

Good LNA will lower the noise figure and improve the conversion gain and on the other side a few MMICs on the TX side will give us pleasure to work some distant stations. Just for the test I add another SNA-586 on the TX side bringing the signal up to the 3dBm. Not much, but at the same time I add another pipe cap filter between the MMIC blocks to reach the cleaner signal at the output. Result can be seen at the video. The same approach can be used to build the transverter for the other microwave bands, so no excuse for the low activity at the microwave bands. 

So "Use them or lose them"

24 GHz transverter update

As I received a few queries regarding the transverter here is the update on done so far. I make some small modifications but nothing that is diverting from the original idea. I did have a big problems with the YIG PLL oscillator MTS1500 which was not working properly. I discovered that the YIG inside the whole unit is faulty, can not be locked neither controlled properly. After so many time devoted to this unit I quit and order the other YIG PLL oscillator DFS-1201 which is working as required, immediately after first start. More over I program two frequencies so the same unit can be used aloso as the LO for the 47GHz operation.

Briefly, here we have a DFS-1201 YIG PLL programmed for L.O./2 frequency to suit the 436MHz IF. DFS-1201 is controlled via the small PCB with the PIC microcontroler (directly on the DFS-1201 connector) where 2 programmed frequencies are available. The output signal is 14dBm and splited in two for upconverter and downconverter. No waveguide relay as mentioned previously, isolator is good enough to protect the downconverter from the 300mW which can produce the TRW upconverter.

The bottom PCB is switching the voltages for the units and acting as a small sequencer together with the IF attenuator and switching.

Power supply boards with the voltage stabilisers are attached to the left/right walls of the plastic housing.

The antenna is attached directly to the third isolator port through the short peace of the WR-42 flexible waveguide. The antenna is not so big and the radom has been dismantled to make this system light and easy for operating. Even not so big the antenna is quite sharp and careful pointing is required.

Some initial test were performed and overall feeling is that the transverter perform very good. The RX NF is very good and the YIG PLL stability after initial warming up of 5 minutes is excellent. Circulator instead of  relay seems to be a very handy because no headache and fear to burn the downconverter front end. No "smart" sequencing is required and loss are reduced to the minimum.

Present ODX is 168.5 km LOS qso during the summer with the humidity close to 90% over the sea path. Winter should be the right time to gain this distance.

73 and CU on 24GHz

W1GHZ cheap 3cm beacon board

Some time ago besides some other PCB's I ordered also the board for the simple 3cm beacon oscillator project from Paul, W1GHZ. The price was really affordable, and you never know when you will need some simple multiplier project like this. The latest, I heard that he is running with stock low of this board, so this means that people are building this stuff more and more. On the other side, not so many feedback on the web regarding the results obtained from this simple multiplier leaving idea that all this projects are working perfect with no problems or they are not working at all and people are giving up without an extra effort to tune properly this interesting approach to old fashioned multiplier idea.

So here it is, completed and tuned multiplier for 10368MHz. Of course, I did make some small modifications to get the best results from this board, at the end it is working. I saw that Paul published the update on this project, but maybe somebody will find my hints useful too. 

The first thing that can be noticed, my tuning screws are quite long, this is not necessary. I did use the same project for some other final frequencies (11808MHz) and I left the screws long enough also for the lower frequencies. The size of the screws: M4 brass for the first (3.5GHz) pipe cap and M3 brass for the other two (10GHz) pipe caps.

Secondly, I did use 9V power supply, instead of 8V. The only reason was the 9V voltage regulator that was handy for me. All MMIC bias resistors are modified to get the best results with 9V.  As there is enough place on the board, I have two resistors in series for each MMIC stage. This way I can easily tune the bias current and the dissipation on resistor is lower, even I am using 1208 SMD bias resistors.

About MMICs, I mount 3x SNA-286 and 2x NLB-310. I went through the data sheets quickly, and I noticed that ERA-1 is quite poor for the 10GHz and decide to use NLB-310. I don't know how Paul manage to get the 11dBm from ERA-1 on 10GHz, but this is not option not even in the data sheet :-)

So, this are all mods. done from my side regarding the original approach. Let's start with tuning...

I have to said that without Spectrum analyzer not reading the Paul's advice, tuning this multiplier can be quite confusing. So, at least any kind of power detector able to detect -10dBm @ 10GHz is a "must" to reach the final result. For the signal generator, I did use the handy Si-4133 generator where i have programmed 16 well known microwave frequencies. 1152MHz and 5dBm is what we need. 

The first pipe cap should be tuned  to x3 = 3456MHz. This should not be a big problem because of the size of the pipe cap that does not allow to tune to the 2nd harmonic frequency. With the screw completely inside, backing the screw a few turns out the strong signal / power peak will be present at certain point at the first SMA tuning point. At this point you are at 3456MHz, all what we need from the first two MMICs and big pipe cap. Backing the screw more out you will reach another peak of the signal, almost the same strength, this is x4 = 4608MHz. If you have a sensitive power meter or detector, backing the screw almost completely out of the pipe cap you can observe some weak peak also on the x5 = 5760MHz frequency. So, this pipe cap can be tuned to 3 different frequencies, our goal is to tune to the lower (first) one.

This step was quite easy, the next one will require more precision and patience. The two 1/2 pipe caps should be tuned to 10368MHz. They are to small to be tuned to the x2 =6912MHz and they are too big to be tuned to x4 = 13824MHz so the only possibility is to tune them to x3 = 10368MHz. With the M3 screws completely inside slowly backing them, some where in the middle of the pipe cap you will notice the power peak at the output SMA. You will need to tune both pipe caps parallel to reach this point. Once you reach the peak, tune the both screws for the maximum output signal. This should bring you on the 10368MHz.

Looking nice, well more about this later :-)

Following this procedure the power I get on the 10GHz was only 0dBm, not even. The first thought was, where the f... I lost the 10dBm?? Driving the multiplier with the different power levels I found the +7dBm  @ 1152MHz gave the best output (+1dBm). But this is still far away from +11dBm...

I start to play with the first MMIC (SNA-286) bias resistors, and there was a nice improvement. I had to increase the resistor almost double to squeeze the maximum from this first multiplier stage. The output power went easily to +5dBm. I thought that same procedure with tuning the third SNA-286 bias multiplier will bring up the output power to desired +10dBm but this was not the case. Changing the bias did not bring any better results. Maybe SNA-286 are not so good in producing the harmonics at higher frequencies??

So, for the moment I stopped here, +5dBm @ 10368MHz is good enough for me, but for sure I will investigate the difference between the ERA-2, SNA-286 and some other MMIC candidates in producing high reach harmonics above 10GHz.

Let's go back to a nice looking signal shape from the picture before. Really nice ha? OK, there is another (fuzzy) shot of the Spectrum analyzer screen.

Not so perfect, ha? Well, believe it or not, this is the same signal from the previous picture. So where is the catch? To simply explain, I will compare this with the Miss universe competition :-) Looking from the balcony all those girls looking nice, but coming closer we can see that some of them are looking not so good as from the balcony. Same here, if you use the span of 100MHz you will get the first picture, if you use the span on the S.A. of 1MHz you can  get the 2nd, more realistic picture.

Well, this have nothing to do with the multiplier, but just want to give you an idea how Si-4133 signal looks after x9 multiplication. I want to gain that my Si-4133 oscillator is using the good quality Isotemp double oven 10MHz reference oscillator, so imagine how the signal will look using the cheap 10MHz canned oscillator.

I get the nice phase noise comparison measurement chart made recently on the MUD 2012 meeting compiled from Paul, W1GHZ. So all credits goes to him and the guy who measure it. Nothing more to add...

At the end, just a few ideas where to use this multiplier, of course the first idea will be a simple 3cm signal beacon source. I did use the same to generate the 11808MHz signal for one of my 24GHz transverters. You can hook up also the Comtech ATV TX tuned to 1161 MHz to reach 10450MHz. Driving this multiplier with the 720MHz can result with the output of 10800MHz which can be a simple L.O. solution for the 10368MHz transverter with the I.F. 432MHz (LSB). So many solutions for the simple multiplier.

By the way, if you manage to reach +11dBm of output power, let me know...

Simple 6cm - 5760 MHz beacon

This is just another simple beacon for 6cm band that came out as a result of raining afternoon and a desk full of various microwave components. Of course, this can be done on many different ways but I choose to use the parts that are cheap and available to every microwave builder. As most of my designs this project is also modular where every component can be replaced with some other, resulting maybe better, maybe worst performance but at the end the output signal level will be within the range of a few dB of difference.

This is a block diagram of the beacon oscillator from my scrapbook. After so many simple project I start to take a notes with at least few measurements so If I need these data later, they are always here in the notebook. Th PC is nice but notebook is better.

So no detail electrical diagram this time because all blocks are explained already through my previous designs. The beacon is built around well known S53MV crystal oscillator used in his beacons or ZIF microwave radios. The 720MHz signal is attenuated to a level of approx. 5dBm to drive more efficiently the 6cm multiplier explained on my blog. As we are dealing with the multiplying factor  of 8, not much of the signal is left at the required frequency of 5760 MHz. This signal is amplified with a two MMICs blocks, the first one withe the NLB-310 and the second one with the SNA-586. The output power is around 10dBm or 10mW. The filter is optional, but recommended, reducing the output power to 8dbm+

Going from the left, the 720MHz oscillator (still not screened) is starting with the 20MHz crystal. This is a common value where also cheap computer grade crystals can work. There is a tuning inductor and trimmer capacitor with possibility to tune desired frequency, in my case at the beginning of the band, but leaving enough room for EME operators. after the multiplying chain (x3 x3 x2 x2) we end up with decent level of 11dbm+ for the next stage.

Maximum allowed input level for the multiplier is +10dbm, so attenuator was required in between. Playing with the attenuator values I found that the 6db attenuator will give the best results, higher output of the multiplier for the 8x multiplying factor.

The multiplier was driven with the 5dBm of the signal for the best performance. Even better results are possible by changing the value of the bias resistor in the first MMIC multiplier stage. Usually higher resistor value will give up to 3dB better output signal for desired input frequency. I did not play with that in this project, so there is room for improvement. I got -9dBm of signal after the multiplier.

MMIC blocks are simple and cheap and they have a decent gain. I choose the two different MMICs to see how they perform at 6GHz. The first one with NLB-310 is working very nice with the 11dB of the gain producing almost +2dBm of the signal. The second one, SNA-586 gives another push to +10dBm with the gain of just litle bite more than 8dB on 6 GHz.

The filter is optional but can be very useful if you plan to use this beacon on remote high location. 3/4 pipe cap filter can be the easiest solution. Just tune the filter to maximum signal and this is enough. Place the filter between the MMICs to isolate them with the I.L. of the filter. After initial attempt my pipe cap filter was inserting 4dB of loss, a bit high. Then after fine tuning I was able to reduce the I.L. to only 1.6dB @ 5760MHz. Inserting the filter the output drops to +8dBm.

The last component (gray)that can be seen is directional coupler. This is not a part of the beacon oscillator. It was used just to simultaneously monitor the signal on the frequency  counter and the spectrum analyzer.

This is the core of the 6cm beacon. The rest of the parts that are required are beacon keyer, power supply and the antenna. The keyer is already explained on the blog, where multiplier stage should be keyed with the positive voltage. Power supply can be anything that can give you 500mA @ 13,6V. The antenna type depend on the requirement, simple horn or slotted waveguide can be a solution or if you want to go really cheap and simple, a simple vertical Wi-Fi 5.7GHz band can be good also but vertical polarization will produce less signal for H-pol weak signal users. For a home use, this is the best-buy option.

Modification TOKO 5HW-1150-45F filter for 23cm band

I have this nice and small (and expensive) helical filter in my drawer for some time. Looking the TOKO filter data-sheet this is very nice filter for the 1152 MHz local oscillator project, but I want to use the same one in my 23cm transverter, for filtering 1296 MHz. The data-sheet states that it is not possible to tune to the desired frequency. Of course, there is another filter covering that particular part of the band but my drawer is not TOKO store :-)

 Going back to the data-sheet... It is clear that this is double tuned helix type filter, center frequency 1195 MHz with the coupling done through the window inside the metal shield. The connection diagram (F connections) in the data-sheet does not give a real situation of the helix inside the shield. From the diagram we can see that there is a helix between the hot end and the ground connection and a small part of the helix continuing after the hot end pin connection. Basically, the idea is just to short the helix to bring the resonance higher using cut and try method, but following the diagram there is nothing much to cut on F version.

On the other side I got the hint from Goran AD6IW that he make the mods. on the same filter very easy and simple and this should work, so this was good reason to try and see what is going on inside the "mystery helix".

Do not be afraid, this is going to be very quick and simple modification. You do not need not even a soldering iron, just a small sharp cutter and a small flat screwdriver. Each of the helix is secured inside the housing with the 4 dents, 2 on each side. Using a tip of a sharp flat screwdriver bent vertically all 4 dents to free the brown helix former. Pull out the the  helix former, and you will have the same situation as from the following photo:

You probably ask yourself the same question I ask myself too, WTF is worth 20$ inside this helix filter ?! Do not look and search for any other parts inside the metal shield, there is nothing else inside except the tuning screw :-)

First thing that you may notice is that the real situation is not the same as on the diagram. The "helix coil" between the hot end and the ground pin is just a bridge from one pin to another, no any helix turns at all, as showed on the diagram. The helix is then extending from the live end pin around the coil former exactly 5 turns. What we need to do is just short the helix to bring the center resonance around the 1296 MHz. Cut and try method was the simplest one and gave excellent result. The helix is soldered on one end to the connecting pin and the other free end is just bended wire inside the gap of the coil former. To bring the resonance up, simply cut and remove just 1/4 of the last wire turn from the helix using the tip of the sharp cutter. The wire is stiff enough to stay on the coil former, but if you feel that the helix will be unwound secure the helix with the drop of super glue. I did not use this method because I didn't know what effect can cause the glue to the coil resonance and Q factor (if any?).

Use the same procedure for the other helix in the filter. After all, insert the coil formers back to the shield and secure them with the same 4 dents from the beginning of the modification.

So that's it, just a 1/4 turn shorter helix solved the problem and the filter is tuning smoothly to the 1296 MHz with almost identical response curve. I did check the filter directly soldering the SMA connector to the live pin and ground shorting the ground pin and shield. This was much simpler than soldering the filter on the special PCB. The proper way of tuning will be using the network analyzer but this is not so common among the HAM experimenters so simple generator, oscillator on 1296 MHz and LNB diode detector can do the job also.

Finally, check this cheap and dirty approach, the LNB IF MMICs (C1H & C1E) board with the modified TOKO filter. -13dB of input gives out filtered +12dB of signal on 1296 MHz. You can use this board both way, for RX & TX, so simple, the half of the 23cm transverter is already here :-)